Preh MCI TOUCH MCI 15T User Manual download pdf (Page 4)

Display Setup and On Screen Display

Connect and secure cables to the display and the computer, except for the USB cable. The AC

cord set provided with your display should be appropriate for your region. If the proper cord set

has not been provided, you may use any cord set with an IEC320 connector at the appliance

end to connect to your touch display.

Notice: Unless your Preh MCI Touch Monitor has a serial data interface, or you are connecting

this MCI Touch Monitor to a computer that already has Preh touchscreen MSR and Customer

Display drivers installed, please leave the USB cable disconnected until the appropriate drivers

for your computer’s operating system have been installed.

On Screen Display Controls

The following table shows the OSD and Power control buttons, located on the right side of the

display, and both the Normal and Direct Access functions of these buttons.

The Direct Access features can be used by pushing the corresponding button without entering

the OSD Menu rst. For example, you may access the Display Brightness feature through

Direct Access by simply pushing the UP button.

Button Symbol Button Name Function/Normal Direct Access

1 Menu Displays/Exits OSD Menu

2 Up Increases selected item value Display brightness

3 Down Decreases selected item value Audio ON/OFF

4 Enter Selects highlighted menu item Video auto adjust

5 Power Turns all display power ON/OFF

Display Setup

Use the OSD buttons to set up the display:

1. Turn on the display with the POWER button.

2. The display will initially be set to properly display the native resolution for the LCD panel,

which is 1024 x 768 pixels. If your computer outputs a video signal at another resolution,

further adjustment than described in this section may be required. Contact Preh Technical

Support at [email protected] if assistance is required.

3. Press the ENTER button on the OSD controls. A pop-up window on the display should

appear with the message “Auto Adjusting Please Wait.”

4. Inspect the top, bottom, left and right edges of a typical application to make sure you can

see the entire image on the display without scrolling. If so, you are nished with the basic setup

of the display.

Display Resolution

If your application requires use of the display at another resolution than 1024 x 768, such

as 800 x 600, you may achieve satisfactory operation by using the Auto Adjust procedure

described above, or you may need to use the individual controls in the OSD to properly adjust

the display. Access the OSD main menu and use the Video Adjustment functions (see table on

next page) to resize, move, or adjust the quality of the displayed image.

OSD Menu and Function

The complete OSD Menu is shown in the table below. The Main Menu icon for each menu

group is shaded, and the individual functions within the group follow. To access the OSD Menu,

push the MENU button.

Use the ENTER button to select a highlighted menu, and to move between individual items

within a menu. Use the UP/DOWN buttons to select/deselect an item, or to increase/decrease

the value of an item.

Contrast & Brightness

Contrast Controls the display contrast.

Brightness Controls the display brightness.

Video Adjustment

Auto Adjust Automatically sets display image size, position, and ne adjustment.

Contrast and brightness are not adjusted.

Left/Right Controls horizontal position.

Up/Down Controls vertical position.

Horizontal Size Increases or decreases the horizontal size of the image.

Fine Controls the vertical ne adjustment. May improve picture detail in

emulation modes.

OSD Tool

OSD Left/Right Adjusts the default horizontal position of the OSD on the display.

OSD Up/Down Adjusts the default vertical position of the OSD on the display.

OSD Timeout Determines time (in seconds) that OSD waits before closing

automatically after no action has been performed.

Factory Reset Recalls original factory settings of image parameters.

OSD Language Selects the OSD menu language: English, French, German, Italian,

Spanish, Japanese, Traditional Chinese, or Simplied Chinese.

Color Adjustment Adjusts preset color temperature of the image. Available choices are

9300, 7500, 6500, and 5500° Kelvin (K). A User mode allows custom

setup of each color component of the image-Red, Green and Blue.

Default setup for this parameter is 6500° K. Do not adjust color

temperature unless you have a specic need to do so.

Audio Adjustment

Volume Adjusts the loudspeaker volume.

Mute ON/OFF Mute ON turns off the audio function. Mute OFF restores the audio.

Auto Dim

Auto DIM Turns the Auto-Sensing Brightness Adjustment circuit ON or OFF.

Dimming Range Menu shows sensed light level, and brightness setting as a percent

age of full scale (same setting as Brightness in Contrast and Brightness

menu when Auto DIM is OFF). With Auto DIM ON, brightness is now

controlled by the light sensor located at top center of the front bezel.

See additional discussion of the Auto-Sensing Brightness Adjustment.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Preh MCI TOUCH MCI 15T User Manual Page 4

Comments to this Manuals